Table of Contents
Upgrading the turbocharger on your Cummins 6.7L is one of the most effective ways to unlock substantial horsepower and torque gains. The Bullseye Power 66/74 turbocharger has become a go-to choice for diesel enthusiasts seeking a balance of quick spool, high flow, and durability. This guide provides a comprehensive, step-by-step walkthrough for installing a Bullseye Power 66/74 turbo on a 6.7L Cummins, along with critical tuning and maintenance insights to ensure you get the most from your upgrade.
Understanding the Bullseye Power 66/74 Turbo
The Bullseye Power 66/74 turbo is a billet wheel, ball-bearing turbocharger designed for medium- to high-horsepower applications on Common Rail Cummins engines. The “66/74” refers to the inducer and exducer diameters of the compressor wheel: 66mm inducer and 74mm exducer. This sizing delivers a significant increase in airflow over the stock HE351 or VS450 turbo, supporting power levels from 500 to over 700 horsepower when paired with proper supporting modifications.
Key features of the Bullseye Power 66/74 include:
- Billet 66/74 compressor wheel for high flow and efficiency
- Ball bearing center cartridge for faster spool and reduced friction
- Oil-cooled and optionally water-cooled bearing system
- Cast turbine housing available in multiple A/R ratios (typically 1.00 or 1.10) to tailor spool and top-end response
- Direct fitment to the Cummins 6.7L exhaust manifold with a standard T3/T4 flange
Compared to the stock turbo, the 66/74 offers a much larger compressor map and a more efficient turbine housing, allowing the engine to breathe better at higher RPM while maintaining responsive spool characteristics for daily driving and towing.
Benefits of Upgrading to the Bullseye Power 66/74
Choosing the 66/74 over other turbo sizes provides a specific set of advantages for 6.7L Cummins owners:
- Increased horsepower ceiling: The 66/74 flows enough air to support 600+ wheel horsepower without choking at the top end.
- Lower exhaust gas temperatures (EGT): More efficient airflow reduces exhaust backpressure, helping keep EGTs in check even under heavy load.
- Improved towing performance: The ball bearing cartridge and optimized turbine spool the turbo quickly, providing strong low-end response for towing heavy trailers.
- Better fuel efficiency: A properly matched turbo that does not require excessive wastegate pressure can improve fuel economy under moderate driving conditions.
- Robust build quality: Bullseye Power uses high-grade billet aluminum and stainless steel components, ensuring longevity and reliability.
It is worth noting that to fully exploit the 66/74’s capabilities, you will almost certainly need upgrades to fuel delivery, intake, and exhaust systems, as well as a custom engine tune. More on that later.
Tools and Materials Needed
Before beginning the installation, gather all necessary tools and replacement parts. Having everything on hand will minimize downtime and prevent frustration.
Required Tools
- Socket set with metric and SAE sockets (10mm, 12mm, 13mm, 15mm, 18mm common)
- Ratchet and extensions (including a wobble extension for tight spaces)
- Torque wrench (capable of 15-75 ft-lbs)
- Combination wrenches
- Pry bar or large flathead screwdriver
- Pick set (for removing old gaskets)
- Penetrating oil (e.g., PB Blaster, Kroil)
- Shop towels and gloves
- Oil drain pan and coolant catch container
- Safety glasses and jack stands
Parts and Consumables
- Bullseye Power 66/74 turbo assembly (with mounting hardware and gaskets)
- New turbo mounting gasket (manifold-to-turbo)
- New exhaust flange gasket (if applicable)
- New oil supply line (often included with the turbo, or upgrade to a braided stainless line)
- New oil drain gasket and o-ring
- Coolant line gaskets (if water-cooled lines are reused)
- Two new intake boots and T-bolt clamps (for the intercooler pipe)
- Anti-seize compound and thread locker (medium strength)
- Fresh engine oil (approximately 1 quart for pre-lubrication)
- Coolant (if lines are disconnected)
It is also wise to have a factory service manual or access to an online forum like Cummins Forum for specific torque values and diagram references.
Pre-Installation Preparation
Proper preparation will save time and prevent damage to your new turbo. Follow these steps before touching any bolts:
- Cool down the engine: Work on a cold engine to avoid burns and to reduce the risk of warping hot manifolds when loosening bolts.
- Disconnect the batteries: Remove both negative terminals to prevent accidental cranking or electrical shorts.
- Drain coolant and oil: If you plan to replace the oil supply or drain lines, drain the engine oil and coolant. Otherwise, you can try to plug the lines, but draining is safer.
- Remove the air intake and intercooler piping: Strip away everything from the turbo inlet and outlet to give yourself room.
- Spray penetrating oil on all exhaust bolts: Especially the turbo-to-manifold bolts and the exhaust downpipe flange nuts. Let it soak for 10-15 minutes.
- Inspect the manifold: Check for cracks or warpage on the stock exhaust manifold. A warped manifold will cause exhaust leaks and poor turbo fitment.
Step-by-Step Installation Guide
The following steps assume you are working on a 2013-2018 6.7L Cummins in a Ram 2500/3500. Other applications may have slight differences, but the general procedure remains the same.
Step 1: Remove the Stock Turbocharger
- Disconnect the oil feed line: Use a line wrench to avoid rounding the nut. Cap the line to prevent debris from entering.
- Remove the oil drain tube: Unbolt the drain from the turbo and the block. Expect some oil spillage.
- Unbolt the exhaust downpipe: Loosen the V-band clamp or bolts connecting the turbo outlet to the downpipe. You may need to remove the downpipe entirely for clearance.
- Disconnect the intake pipe: Loosen the boot clamp and pull the pipe off the turbo inlet.
- Remove the intercooler pipe: Unbolt or unclamp the charge air pipe from the turbo outlet.
- Unbolt the turbo from the manifold: Using a socket and extension, remove the four (or six) bolts holding the turbo to the manifold. The rear bolt is often the most difficult; a wobble extension or universal joint helps.
- Lift the turbo out: Carefully wiggle the turbo free from the manifold and exhaust downpipe flange. Watch for any remaining oil or coolant.
- Clean the manifold face: Use a gasket scraper to remove any old gasket material. Apply a thin coat of anti-seize to the manifold studs.
Note: If the manifold studs come out with the nuts, replace them with new studs or bolts to ensure proper torque.
Step 2: Prepare the Bullseye Power 66/74 Turbo
- Inspect the turbo: Confirm no shipping damage. Spin the compressor wheel by hand – it should rotate smoothly with no axial or radial play.
- Pre-lubricate the bearings: Pour about 1/2 cup of clean engine oil into the oil inlet port while slowly rotating the wheel. This primes the bearing cartridge and prevents dry start.
- Check the wastegate actuator: If your 66/74 comes with an external or internal wastegate, verify the actuator arm moves freely and the spring preload is appropriate for your target boost level.
- Install the oil drain gasket: Use the supplied gasket and apply a thin layer of gasket maker to both sides for a leak-free seal.
- Attach the oil feed line: If the turbo includes a new line, install it now. Torque to 18-20 ft-lbs.
Step 3: Install the Bullseye Power Turbo
- Position the turbo on the manifold: Lift the turbo into place, aligning the holes with the manifold studs. A second set of hands or a jack can help support the weight.
- Install the mounting bolts: Thread the five (or six) bolts by hand, then torque them in a cross pattern to 55-60 ft-lbs (or per manufacturer spec).
- Connect the oil drain tube: Attach the drain tube to the turbo and the engine block. Tighten bolts to 10-12 ft-lbs. Do not overtighten the aluminum drain flange.
- Connect the oil feed line: Tighten the line nut to 16-18 ft-lbs.
- Connect coolant lines (if applicable): Some 66/74 setups are water-cooled. Reattach the coolant supply and return hoses, using new crush washers if required. Torque to 18 ft-lbs.
- Attach the intake pipe: Slide the intake boot over the compressor inlet and secure with a T-bolt clamp. Do not overtighten.
- Attach the intercooler pipe: Connect the charge air pipe to the turbo outlet using the new boot and clamp. Ensure the pipe seats fully.
- Connect the exhaust downpipe: Use a new gasket if supplied, and tighten the V-band clamp or bolts evenly.
- Reconnect the wastegate actuator line (if applicable): Use high-quality silicone hose and clamps. Route the boost reference line to the intake manifold appropriate port.
Step 4: Reassembly and Initial Checks
- Reconnect the battery: Positive first, then negative.
- Prime the oil system: Unplug the fuel injector harness (or crank with the fuel shut-off solenoid disabled) and crank the engine for 10-15 seconds without starting. This circulates oil into the turbo bearings. Let the starter cool for 2 minutes, then repeat once more.
- Start the engine: Start the engine and let it idle for 3-5 minutes. Listen for any unusual whistling, scraping, or knocking.
- Check for leaks: Inspect all oil, coolant, intake, and exhaust connections. Use a mirror or camera for hard-to-see areas. Tighten any leaky fittings.
- Monitor boost and EGT: If possible, take a short test drive while monitoring boost pressure and exhaust gas temperatures. Do not exceed 15 PSI of boost or 1200°F EGT before tuning.
Post-Installation Tuning and Considerations
Installing the Bullseye Power 66/74 is only half the battle. Without proper tuning, the larger turbo can cause sluggish spool, excessive smoke, and even engine damage. Here is what you need to address:
- Custom tuning is mandatory: Stock ECM calibration cannot properly control fuel delivery to match the new airflow. You will need a tuner (e.g., EFILive, H&S, or PPEI) and a custom tune from a reputable Diesel tuner like PPEI or Firepunk Diesel.
- Fuel system upgrades: To take full advantage of the 66/74, you may need larger injectors (e.g., 75% over stock), a high-pressure CP3 pump, or an auxiliary fuel system.
- Intake and exhaust upgrades: A free-flowing cold air intake and a 4-inch turbo-back exhaust system will reduce backpressure and improve spool.
- Upgraded intercooler: The stock intercooler can become a restriction at higher boost levels. Consider an upgraded unit for sustained power.
- Transmission updates: If you have an automatic (68RFE, Aisin), increase line pressure and shift firmness to handle the additional torque. A torque converter with a billet stator is highly recommended.
- Gauges: Install a digital boost gauge, EGT probe, and fuel pressure gauge to monitor vitals in real-time.
Also, give the turbo a break-in period of 500 miles before towing heavy loads or running high boost. Gradually increase load to allow the bearings to seat properly.
Maintenance and Longevity Tips
To keep your Bullseye Power 66/74 in peak condition, follow these maintenance practices:
- Frequent oil changes: Use high-quality diesel oil (15W-40 or 5W-40 synthetic) and change every 5,000 miles. The turbo’s ball bearing system relies on clean oil.
- Inspect the air filter regularly: A dirty filter increases restriction and can lead to turbo overspeed or contaminant ingestion. Replace annually or sooner in dusty environments.
- Check for boost leaks: Loose boots or cracked intercooler pipes cause poor spool and high EGTs. Perform a boost leak test every 10,000 miles.
- Monitor wastegate operation: If your turbo has an external gate, ensure the actuator rod moves freely and the boost reference line is not kinked.
- Let the turbo cool down: After hard driving, idle the engine for 1-2 minutes before shutoff to cool the bearings and prevent coking.
Frequently Asked Questions
Will the Bullseye Power 66/74 fit on a stock 6.7L Cummins?
Yes, it is a direct bolt-on replacement for the stock turbo on factory exhaust manifolds. However, the stock intake and intercooler piping may need slight modifications for optimal fitment.
Do I need upgraded injectors for the 66/74?
For power levels under 500 hp, stock injectors can work with a tune. Above that, upgraded injectors are necessary to prevent excessive smoke and high EGTs.
Can I tow with this turbo?
Absolutely. The 66/74 spools quickly and provides excellent low-end torque for towing. Proper tuning and exhaust brake compatibility are important.
How much boost will this turbo produce?
With appropriate tuning, you can safely run 40-50 PSI. The ball bearing design handles high shaft speeds without issue.
Is a turbo blanket recommended?
Yes. A high-quality turbo blanket reduces under-hood temperatures, improves spool, and protects nearby components from radiant heat.
Conclusion
Installing a Bullseye Power 66/74 turbo on your Cummins 6.7L is a proven path to significant power gains and improved drivability. By following this detailed installation guide and paying careful attention to post-installation tuning and maintenance, you can achieve a reliable, high-performance setup that transforms your truck. Whether you are chasing track times or pulling heavy loads, the 66/74 offers the airflow and durability needed to get the job done. For further technical specifications and ordering information, visit the Bullseye Power official website.