Table of Contents
The Mitsubishi Lancer Evolution X, commonly known as the Evo X, is a beloved performance vehicle among car enthusiasts. One of the most popular modifications for this car is the COBB Stage 2 Tune, which enhances engine performance and overall driving experience. This guide will walk you through the step-by-step process of installing the COBB Stage 2 Tune on your Evo X.
What You Will Need
- COBB Accessport V3
- Computer with internet access
- USB cable for Accessport
- Basic hand tools (screwdrivers, wrenches)
- Optional: Torque wrench
Before you begin, ensure that your Evo X is in good condition and ready for tuning. It is advisable to perform any necessary maintenance before proceeding with the installation.
Step 1: Download the COBB Software
Start by downloading the COBB Tuning software on your computer. This software is essential for transferring the Stage 2 Tune to your Accessport.
Access the COBB Website
Visit the official COBB Tuning website and navigate to the downloads section. Here, you will find the necessary software for your Accessport.
Install the Software
Follow the instructions to install the COBB software on your computer. Make sure to complete the installation before proceeding to the next step.
Step 2: Connect the Accessport to Your Computer
Once the software is installed, connect your COBB Accessport to your computer using the USB cable. Ensure that the connection is secure.
Step 3: Update the Accessport Firmware
Before uploading the tune, it is essential to update the firmware on your Accessport to the latest version.
Check for Updates
Open the COBB software and look for the option to check for firmware updates. Follow the prompts to update your Accessport.
Step 4: Download the Stage 2 Tune
After updating the firmware, the next step is to download the COBB Stage 2 Tune specifically designed for the Evo X.
Select the Correct Tune
In the COBB software, navigate to the tuning section and select the Stage 2 Tune for your vehicle. Ensure that it is compatible with your specific model and modifications.
Upload the Tune
Once you have selected the correct tune, follow the instructions in the software to upload the tune to your Accessport. This process may take a few minutes.
Step 5: Install the Accessport in Your Evo X
After successfully uploading the tune, it’s time to install the Accessport in your Evo X. This process is straightforward and can be done in a few simple steps.
Locate the OBD-II Port
The OBD-II port is typically located under the dashboard near the driver’s seat. Make sure your vehicle is turned off before proceeding.
Connect the Accessport
Plug the Accessport into the OBD-II port. Once connected, turn on the ignition without starting the engine. The Accessport will power on automatically.
Step 6: Flash the Tune to Your Vehicle
With the Accessport connected, it’s time to flash the Stage 2 Tune to your Evo X. This process will overwrite the factory settings with the new tune.
Follow the On-Screen Instructions
The Accessport will guide you through the flashing process. Follow the on-screen instructions carefully to ensure a successful installation.
Wait for the Process to Complete
Do not turn off the ignition or disconnect the Accessport during the flashing process. Wait until the Accessport indicates that the installation is complete.
Step 7: Verify the Tune Installation
After successfully flashing the tune, it’s crucial to verify that the installation was done correctly. This ensures that your vehicle is running optimally with the new tune.
Check for Error Codes
Use the Accessport to check for any error codes that may have appeared during the installation. If there are no codes, your installation was successful.
Test Drive Your Evo X
Take your Evo X for a test drive to experience the improvements from the Stage 2 Tune. Pay attention to the throttle response and overall performance.
Step 8: Troubleshooting Common Issues
If you encounter any issues during the installation process, here are some common problems and solutions.
- Accessport Not Recognized: Ensure the USB cable is securely connected and try a different USB port on your computer.
- Flashing Error: Restart the Accessport and try the flashing process again. Make sure the vehicle battery is fully charged.
- Check Engine Light: If the check engine light turns on after installation, use the Accessport to read the error codes and troubleshoot accordingly.
Conclusion
Installing the COBB Stage 2 Tune on your Evo X can significantly enhance your driving experience. By following this step-by-step guide, you can ensure a successful installation and enjoy the benefits of improved performance. Always remember to monitor your vehicle’s performance after tuning and consult with professionals if you encounter any issues.